Fast3DEX2 Display List Commands [Hack64 Wiki]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

====== Fast3DEX2 Display List Commands ======
The Fast3DEX2 display list commands are microcode that are passed to the RSP for rendering. They are all 8 bytes long.

===== Fast3DEX2 Commands =====

==== 00: G_SPNOOP ====
Stalls the signal processor (the RSP), and as a consequence, the RDP too. This should only be used for debugging purposes.

''00 00 00 00 00 00 00 00''

==== 01: G_VTX ====
Fills the vertex buffer with vertex information (ex. coordinates, color values).  Max amount of vertices to load in F3DEX2 is 0x20 (32).

''01 0[<color #22b14c>N N</color>]0 [<color #ed1c24>II</color>] [<color #A946F2>SS SS SS SS</color>]''


| <color #22b14c>N</color> | Number of vertices to write |
| <color #ed1c24>I</color> | Where to start writing vertices inside the vertex buffer (start = <color #ed1c24>II</color> - <color #22b14c>N</color>*2) |
| <color #A946F2>S</color> | Segmented address to load vertices from |

Example: Load 4 vertices from 0x0E000780 and put them into the vertex buffer, starting at position 0.
  01 00 40 08 0E 00 07 80


==== 02: G_MODIFYVTX ====
Modifies a four-byte portion of the vertex specified.

''02 <color #ff7f27>ww</color> <color #00a2e8>nn nn</color> <color #C250FF>vv vv vv vv</color>''

| <color #ff7f27>w</color> | Enumerated set of values specifying what to change |
| <color #00a2e8>n</color> | Vertex buffer index of vertex to modify (*2) |
| <color #C250FF>v</color> | New value to insert |

The portion modified is specified by <color #ff7f27>w</color>, and the new value is given in <color #C250FF>v</color>. Lighting calculations (if enabled) and position transformations are not calculated by the RSP after use of this command, so modifications modify final color and vertices.

The valid values for <color #ff7f27>w</color> have names as follows:
  * <color #22b14c>G_MWO_POINT_RGBA</color> = 0x10 Modifies the color of the vertex
  * <color #22b14c>G_MWO_POINT_ST</color> = 0x14 Modifies the texture coordinates
  * <color #22b14c>G_MWO_POINT_XYSCREEN</color> = 0x18 Modifies the X and Y position
  * <color #22b14c>G_MWO_POINT_ZSCREEN</color> = 0x1C Modifies the Z position (lower four nybbles of <color #C250FF>v</color> should always be zero for this modification)

The exact nature of these values is unclear. The SDK documentation describes them as "byte offsets", however they don't match offsets in the vertex structure.
----

==== 03: G_CULLDL ====

''03 00 <color #22b14c>vv vv</color> 00 00<color #00a2e8> ww ww</color>''

| <color #22b14c>v</color> | Vertex buffer index of first vertex for bounding volume (*0x02) |
| <color #00a2e8>w</color> | Vertex buffer index of last vertex for bounding volume (*0x02) |

This command takes the vertices in the vertex buffer from vfirst through vlast as describing the volume of the object being rendered (called the "bounding value"). If the bounding volume does not intersect with the current viewing volume (aka if the bounding volume is entirely offscreen), then the display list ends, equivalent to a B8 opcode. Otherwise, the display list continues as though nothing happened (equivalent to 00, then).

For F3DEX2, Each of vfirst and vlast must be in the range 0 ≤ x ≤ 31. Additionally, vfirst < vlast must be true (thus a minimum of two vertices must be specified, and range of vertices cannot be reversed). It's not specified what the behavior is when all the vertices are coplanar.
----

==== 04: G_BRANCH_Z ====
Tests the Z value of the vertex at a buffer index against a given z-value. 

''//E1 00 00 00 [<color #A946F2>dd dd dd dd</color>]//''

''04 [<color #22b14c>aa a</color>][<color #00a2e8>b bb</color>] [<color #ff7f27>zz zz zz zz</color>]''

| <color #A946F2>d</color> | Address of display list to branch to |
| <color #22b14c>a</color> | Vertex buffer index of vertex to test(*5) |
| <color #00a2e8>b</color> | Vertex buffer index of vertex to test(*2) |
| <color #ff7f27>z</color> | Z value to test against |

If the given vertex's Z value ≤ <color #ff7f27>z</color>, then the processor switches over to the display list at address <color #A946F2>d</color> (equivalent to 06 jump with no return stored). Otherwise continues through the display list. Useful for LOD-related model processing, where several occurrences of this can be stacked to branch to progressively closer versions of the model.

Note that the 04 opcode actually pulls the address of the branching display list from the high half of the "RDP word" (16 bytes used for generic value storage, as far as is known). The italicized opcode given above is set by the "basic function" listed for this opcode, immediately before the actual 04 opcode.

Although not stated in the documentation, the vertex buffer index is presumably limited to the range 0 ≤ index ≤ 31 just like other buffer indices. It's unknown why the opcode needs the index twice, and multiplied by different amounts.

Also, <color #ff7f27>z</color> is usually calculated for the N64 programmer (only the *Zraw form specifies a raw z value). The formula used in these cases is as shown, written as C code:

<WRAP center round box 60%>
<color #733333>#include <stdint.h></color>

int32_t <color #99d9ea>FTOFIX32</color>(float x)
{
    return (int32_t)( x * 0x00010000);
}

<color #22814c>/* note: parameter types taken from docs on gSPBranchLessZrg(...) */</color>\\ 
uint32_t <color #99d9ea>calcZVal</color>(float <color #ed1c24>zval</color>, int32_t <color #ed1c24>flag</color>, float <color #ed1c24>near</color>, float <color #ed1c24>far</color>, int32_t <color #ed1c24>zmin</color>, int32_t <color #ed1c24>zmax</color>) {\\ 
    float part1 = (flag == <color #b5e61d>G_BZ_PERSP</color>)\\ 
                ? (1.0f - <color #ed1c24>near</color> / <color #ed1c24>zval</color>) / (1.0f - <color #ed1c24>near</color> / <color #ed1c24>far</color>)\\ 
                : (<color #ed1c24>zval</color> - <color #ed1c24>near</color>) / (<color #ed1c24>far</color> - <color #ed1c24>near</color>);\\ 
    return (uint32_t)FTOFIX32(part1) * ((<color #ed1c24>zmax</color> - <color #ed1c24>zmin</color>) & ~1) + FTOFIX32((float)<color #ed1c24>zmin</color>);\\ 
}
</WRAP>

Where //<color #ed1c24>zval</color>// is the Z value the programmer is thinking of comparing against (whereas the "real" Z value handed to the opcode is calculated by this function), //<color #ed1c24>near</color>// and //<color #ed1c24>far</color>// denote the distances of the near and far clipping planes, respectively, from the viewpoint. //<color #ed1c24>zmin</color>// and //<color #ed1c24>zmax</color>// are the minimum and maximum possible Z values, respectively. //<color #ed1c24>flag</color>// decides on the projection, taking either of these enumerations:

  * <color #b5e61d>G_BZ_PERSP</color> = 0
  * <color #b5e61d>G_BZ_ORTHO</color> = 1

As their names would suggest, //<color #b5e61d>PERSP</color>// handles perspective projection, //<color #b5e61d>ORTHO</color>// handles orthographic.\\ 
Note that in a default setup, //<color #ed1c24>zmin</color>// is __0__, and //<color #ed1c24>zmax</color>// is __0x03FF__.

This formula cannot be reversed for the value provided in the microcode, since the necessary information is absent. (Since the values are provided in the macro call generating this opcode, there's no guarantee any of the values match what they're "supposed" to be, e.g. //<color #ed1c24>near</color>// could be set to something far different from the location of the actual near clipping plane.)

**Note:** This command works differently in F3DZEX.
----
==== 05: G_TRI1 ====
Renders one triangle according to the vertices inside the vertex buffer

''05 [<color #ed1c24>AA</color>] [<color #22b14c>BB</color>] [<color #00a2e8>CC</color>] 00 00 00 00''

| <color #ed1c24>A</color> | First vertex to use for the triangle (* 0x02) |
| <color #22b14c>B</color> | Second vertex to use for the triangle (* 0x02) |
| <color #00a2e8>C</color> | Third vertex to use for the triangle (* 0x02) |

Example: Render a triangle using the vertex data specified at the vertex buffer positions 0, 1 (0x02 / 0x02) and 2 (0x04 / 0x02).

  05 00 02 04 00 00 00 00

----

==== 06: G_TRI2 ====
Renders two triangles according to the vertices inside the vertex buffer

''06 [<color #ed1c24>AA</color>] [<color #22b14c>BB</color>] [<color #00a2e8>CC</color>] 00 [<color #ff7f27>DD</color>] [<color #ffc90e>EE</color>] [<color #A946F2>FF</color>] ''

| <color #ed1c24>A</color> | First vertex to use for the triangle (* 0x02) |
| <color #22b14c>B</color> | Second vertex to use for the triangle (* 0x02) |
| <color #00a2e8>C</color> | Third vertex to use for the triangle (* 0x02) |
| <color #ff7f27>D</color> | Fourth vertex to use for the triangle (* 0x02) |
| <color #ffc90e>E</color> | Fifth vertex to use for the triangle (* 0x02) |
| <color #A946F2>F</color> | Sixth vertex to use for the triangle (* 0x02) |

Example: Render a triangle using the vertex data specified at the vertex buffer positions 0, 1 (2/2) and 2 (4/2), along with a //second// triangle at vertex buffer positions 3 (6/2), 4 (8/2), and 5 (0x0A/2).

  06 00 02 04 00 06 08 0A

----

==== 07: G_QUAD ====
Renders one quad according to the vertices inside the vertex buffer

''07 [<color darkred>AA</color>] [<color darkgreen>BB</color>] [<color darkblue>CC</color>] 00 [<color red>DD</color>] [<color green>EE</color>] [<color blue>FF</color>]''

| <color darkred>A</color> | First vertex to use for the quad (*2) |
| <color darkgreen>B</color> | Second vertex to use for the quad (*2) |
| <color darkblue>C</color> | Third vertex to use for the quad (*2) |
| <color red>D</color> | Fourth vertex to use for the quad (*2) |
| <color green>E</color> | Fifth vertex to use for the quad (*2) |
| <color blue>F</color> | Sixth vertex to use for the quad (*2) |

Example: Render a quad using the vertex data specified at the vertex buffer positions 0, 1 (2/2), 2 (4/2), 0, 2 (4/2) and 3 (6/2).
  07 00 02 04 00 00 04 06

Note: This opcode is //functionally equivalent// to opcode 06. The macro for this opcode (and thus presumably also the opcode itself) is labeled as //no longer supported// in Oct 1999 SDK documentation.
----

==== D3: G_SPECIAL_3 ====
Appears to be an explicitly reserved command.

''D3 <color #c3c3c3>?? ?? ?? ?? ?? ?? ??</color>''

----

==== D4: G_SPECIAL_2 ====
Appears to be an explicitly reserved command.

''D4 <color #c3c3c3>?? ?? ?? ?? ?? ?? ??</color>''

----

==== D5: G_SPECIAL_1 ====
Appears to be an explicitly reserved command.

''D5 <color #c3c3c3>?? ?? ?? ?? ?? ?? ??</color>''

----
==== D6: G_DMA_IO ====
Does a DMA between DMEM/IMEM.

''D6 [<color #c3c3c3>xx x</color>][<color #00a2e8>s ss</color>] [<color #22b14c>rrrrrrrr</color>]''

''xx = <color #00a2e8>f</color><color #C250FF>mmm mmmm mmm</color>0'' (binary)

| <color #ed1c24>f</color> | Chooses between read or write |
| <color #C250FF>m</color> | ((Address in DMEM/IMEM)/8) & 0x3FF |
| <color #00a2e8>s</color> | (Presumably) size of data to transfer (-1) |
| <color #22b14c>r</color> | DRAM address |

<color #00a2e8>s</color> bytes are presumably transferred in the process. <color #ed1c24>f</color> determines the type of transfer. Apparently:

  * <color #ed1c24>f</color> == 0: Read from DMEM/IMEM to DRAM
  * <color #ed1c24>f</color> == 1: Write DRAM to DMEM/IMEM

The exact nature of this command is unclear, since none of this opcode's macros are documented, and the only available comment suggests this is a debugging tool only. Therefore, you should not expect to see this in production code.
----
==== D7: G_TEXTURE ====
Sets the texture scaling factor.

''D7 00 [<color #c3c3c3>xx</color>] [<color #ff7f27>nn</color>] [<color #ed1c24>ss ss</color>] [<color #22b14c>tt tt</color>]''

''<color #c3c3c3>xx</color> = 00<color #c400da>LL L</color><color #00a2e8>ddd</color>''

| <color #ff7f27>n</color> | Enable/Disable Tile Descriptor (__**2**__=enable, 0=disable) |
| <color #ed1c24>s</color> | Scaling factor for S axis (horizontal) |
| <color #22b14c>t</color> | Scaling factor for T axis (vertical) |
| <color #c400da>L</color> | Maximum number of mipmap levels aside from the first |
| <color #00a2e8>d</color> | Tile descriptor to enable/disable |

Note that scaling factors are binary fractional values with an implied 0.; for example, a scaleS of 0x8000 means 0b0.1000_0000_0000_0000, or 0d0.5.

Examples:
  D7 00 00 02 FF FF FF FF : Standard - at start for extremely close to 1 scaling enabled on tile desc 0.
  D7 00 00 02 80 00 80 00 : Standard - at start for 0.5 scaling enabled on tile desc 0.
  D7 00 00 02 0F 80 07 C0 : Scale for environment mapping 64x32 and enable tile desc 0.
  D7 00 00 00 FF FF FF FF : Disable tile descriptor 0 (end of DL).

----

==== D8: G_POPMTX ====
Pops num matrices from the stack specified by modelview matrix stack.

''D8380002 <color #00a2e8>aaaaaaaa</color>''

| <color #00a2e8>a</color> | (The number of matrices to pop) * 64|

----

==== D9: G_GEOMETRYMODE ====
Enables **and** disables certain geometry parameters (ex. lighting, front-/backface culling, Z-buffer).

''D9 [<color #22b14c>CC CC CC</color>] [<color purple>SS SS SS SS</color>]''

| <color #22b14c>C</color> | ~(Various parameters to clear) |
| <color purple>S</color> | Various parameters to set |

Note: Parameters that are cleared have their bits inverted in the opcode. FF FF FF, for example, would disable nothing.

Parameters:\\ 
See [[https://hack64.net/wiki/doku.php?id=rcpstructs#rsp_geometry_mode|RSP Geometry Mode]] under RCP Structs.

----

==== DA: G_MTX ====
Apply transformation matrix. Used in HUD text printing code to translate textures, as well as copious other transformations including animations.

''DA 38 00 [<color darkred>PP</color>] [<color purple>AA AA AA AA</color>]''

| <color darkred>P</color> | Parameters **^** G_MTX_PUSH |
| <color purple>A</color> | Segmented address of vectors |

Parameters (can be OR'd together):
| 0x04 | projection (default: model view) |
| 0x02 | load (default: multiply) |
| 0x01 | push (default: no push) |

Example: Push matrix and and multiply by matrix at 0x00213DF8; Multiply by matrix at 0x00213DB8
  DA 38 00 00 00 21 3D F8
  DA 38 00 01 00 21 3D B8

----

==== DB: G_MOVEWORD ====
Loads a new 32-bit value data to the location specified by index and offset.

''DB <color #00a2e8>ii</color> <color #22b14c>oo oo</color> <color #A946F2>dd dd dd dd</color>''
| <color #00a2e8>i</color> | Index into DMEM pointer table(?) |
| <color #22b14c>o</color> | Offset from the indexed base address(?) |
| <color #A946F2>d</color> | New 32-bit value |

<color #00a2e8>**i**</color> is an index into a table of DMEM addresses. The enumerations given for this are:

| <color #22b14c>G_MW_MATRIX</color> | 0x00 | Allows direct modification of part of the current MP (modelview * projection) matrix (which is calculated upon loading of either kind of matrix), modifying two elements' integer or fractional parts. |
| <color #22b14c>G_MW_NUMLIGHT</color> | 0x02 | Specifies the number of directional/diffuse lights. (The lighting system always has an ambient light.) |
| <color #22b14c>G_MW_CLIP</color> | 0x04 | Specifies the ratio between the clipping and scissoring boxes. |
| <color #22b14c>G_MW_SEGMENT</color> | 0x06 | Sets up the physical address of a segment. |
| <color #22b14c>G_MW_FOG</color> | 0x08 | Specifies the multiplier and offset for fog effects. |
| <color #22b14c>G_MW_LIGHTCOL</color> | 0x0A | Changes the color of a light without changing the direction |
| <color #22b14c>G_MW_FORCEMTX</color> | 0x0C | Tells the RCP if the MP matrix has been forcibly changed(?) |
| <color #22b14c>G_MW_PERSPNORM</color> | 0x0E | Sets amount by which to scale the W axis value before dividing X, Y, and Z by it. |

The offset is, as the name suggests, an offset from the address that index resolves to. Enumerations are also provided for this value, for each of the enumerated index values. (XXX where to put them? It's a bit of a list.)
----

==== DC: G_MOVEMEM ====
Takes a block of memory from an address and puts it in the location pointed to by an index and an offset.

''DC [<color #ff1010>nn</color>] [<color #ff7f27>oo</color>] [<color #00a2e8>ii</color>] [<color #A946F2>aa aa aa aa</color>]''

| <color #ff1010>n</color> | (((//Size in bytes of memory to be moved//) >> 3)+1)*8 |
| <color #ff7f27>o</color> | Offset from indexed base address (*8) |
| <color #00a2e8>i</color> | Index into table of DMEM addresses |
| <color #A946F2>a</color> | Segmented address of memory |

<color #00a2e8>**i**</color> is an index into a table of addresses of DMEM. Given enumerations for <color #00a2e8>**i**</color> are:
  * <color #22b14c>G_MV_MMTX</color> = 2
  * <color #22b14c>G_MV_PMTX</color> = 6
  * <color #22b14c>G_MV_VIEWPORT</color> = 8
  * <color #22b14c>G_MV_LIGHT</color> = 10
  * <color #22b14c>G_MV_POINT</color> = 12
  * <color #22b14c>G_MV_MATRIX</color> = 14

Note however that only <color #22b14c>VIEWPORT</color>, <color #22b14c>LIGHT</color>, and <color #22b14c>MATRIX</color> are used by any of the macros given to programmers.

Example: Loads diffuse RGBA from 0x0 in Segment 0x0E; loads ambient RGBA from 0x08 in Segment 0x0E
  DC 86 00 10 0E 00 00 00
  DC 88 00 10 0E 00 00 08

----

==== DD: G_LOAD_UCODE ====
Loads a new microcode executable into the RSP.

''//E1 00 00 00 [<color #A946F2>dd dd dd dd</color>]//''\\ 
''DD 00 [<color #ff7f27>ss ss</color>] [<color #22b14c>tt tt tt tt</color>]''

<color #A946F2>d</color> points to the start of the data section and <color #22b14c>t</color> to the start of the text section, with <color #ff7f27>s</color> specifying the size of the data section. After loading the new microcode, the RCP is reset as appropriate.

Note that <color #A946F2>d</color> is stored in the high half of the "RDP word", the opcode for which is shown in italics before the actual DD opcode.
----

==== DE: G_DL ====
Signifies the start of a Display List. May be used to link data and branch the current DL.

''DE [<color blue>AA</color>] 00 00 [<color purple>BB BB BB BB</color>]''

| <color blue>AA</color> | 00 = store return address, 01 = don't store (end DL after branch) |
| <color purple>B</color> | Segmented Address to branch to |

Example: Loads a display list from 0xA50 in segment 0x07.
  DE 00 00 00 07 00 0A 50

----

==== DF: G_ENDDL ====
Terminates the current Display List

''DF 00 00 00 00 00 00 00''

----

==== E0: G_NOOP ====
Does nothing. Seemingly different from 00; judging by the names and position of this opcode and 00, this opcode stalls the RDP, whereas the other stalls the RSP.

''E0 00 00 00 00 00 00 00''

----

==== E1: G_RDPHALF_1 ====
This opcode sets the higher half of the generic RDP word.

''E1 00 00 00 [<color #22b14c>hh hh hh hh</color>]''

| <color #22b14c>h</color> | New value of high word |

**Note:** the referenced function also generates opcode F1. See the section on F1 for info on that.

----

==== E2: G_SetOtherMode_L ====
Modifies various bits of the lower half of the RDP Other Modes word.

''E2 00 [<color #ed1c24>ss</color>] [<color #22b14c>nn</color>] [<color #00a2e8>dd dd dd dd</color>]''

| <color #ed1c24>s</color> | 32 - (Amount mode-bits are shifted by) - (Number of bits affected) |
| <color #22b14c>n</color> | (Number of mode-bits affected) - 1 |
| <color #00a2e8>d</color> | Mode-bits |

The operation performed by the opcode can be expressed as such, assuming <color #C372FF>LO</color> to stand for the lower word of the RDP other modes:

<WRAP center round box 60%>
<color #C372FF>LO</color> =  <color #C372FF>LO</color> & ~(((1 << <color #22b14c>n</color>) - 1) << <color #ed1c24>s</color>) | <color #00a2e8>d</color>
</WRAP>

Or, in English, it clears all the bits designated to be modified (determined by <color #ed1c24>s</color> and <color #22b14c>n</color>), and then sets those bits according to data. Important to note that mode-bits //are **preshifted**//. That is, it is up to the caller to shift data appropriately. The enumerations provided for data are pre-shifted to match this requirement.\\ The enumerations provided for <color #ed1c24>s</color> are:
  * <color #ff7f27>G_MDSFT_ALPHACOMPARE</color> = 0
  * <color #ff7f27>G_MDSFT_ZSRCSEL</color> = 2
  * <color #ff7f27>G_MDSFT_RENDERMODE</color> = 3

The structure of the lower modes is provided [[https://hack64.net/wiki/doku.php?id=rcpstructs#lower-half_bits|in the RCP structs page]].

----

==== E3: G_SetOtherMode_H ====
Modifies various bits of the lower half of the RDP Other Modes word.

''E3 00 [<color #ed1c24>ss</color>] [<color #22b14c>nn</color>] [<color #00a2e8>dd dd dd dd</color>]''

| <color #ed1c24>s</color> | 32 - (Amount mode-bits are shifted by) - (Number of bits affected) |
| <color #22b14c>n</color> | (Number of mode-bits affected) - 1 |
| <color #00a2e8>d</color> | Mode-bits |

Like with E2, data is preshifted, and the opcode's procedure can be formulised in the same way (where <color #C372FF>OH</color> stands for the high word of the other modes):

<WRAP center round box 60%>
<color #C372FF>OH</color> =  <color #C372FF>OH</color> & ~(((1 << <color #22b14c>n</color>) - 1) << <color #ed1c24>s</color>) | <color #00a2e8>d</color>
</WRAP>

The enumerations provided for <color #ed1c24>s</color> are:
  * <color #ff7f27>G_MDSFT_BLENDMASK</color> = 0
  * <color #ff7f27>G_MDSFT_ALPHADITHER</color> = 4
  * <color #ff7f27>G_MDSFT_RGBDITHER</color> = 6
  * <color #ff7f27>G_MDSFT_COMBKEY</color> = 8
  * <color #ff7f27>G_MDSFT_TEXTCONV</color> = 9
  * <color #ff7f27>G_MDSFT_TEXTFILT</color> = 12
  * <color #ff7f27>G_MDSFT_TEXTLUT</color> = 14
  * <color #ff7f27>G_MDSFT_TEXTLOD</color> = 16
  * <color #ff7f27>G_MDSFT_TEXTDETAIL</color> = 17
  * <color #ff7f27>G_MDSFT_TEXTPERSP</color> = 19
  * <color #ff7f27>G_MDSFT_CYCLETYPE</color> = 20
  * <color #ff7f27>G_MDSFT_COLORDITHER</color> = 22
  * <color #ff7f27>G_MDSFT_PIPELINE</color> = 23

The structure of the higher modes is provided [[https://hack64.net/wiki/doku.php?id=rcpstructs#lower-half_bits|in the RCP structs page]].

----

==== E4: G_TEXRECT ====
Draws a textured 2D rectangle on the screen

''E4 [<color darkred>xx x</color>][<color darkgreen>y yy</color>] 0[<color darkblue>I</color>] [<color red>XX X</color>][<color green>Y YY</color>]''\\
''E1 00 00 00 [<color #BF9F00>SS SS</color>] [<color #8F3F10>TT TT</color>]''\\
''F1 00 00 00 [<color #3F3FFF>DD DD</color>] [<color darkcyan>EE EE</color>]''

| <color darkred>xxx</color> | Lower-right corner X coordinate |
| <color darkgreen>yyy</color> | Lower-right corner Y coordinate |
| <color darkblue>I</color> | Tile descriptor to use for rectangle |
| <color red>XXX</color> | Upper-left corner X coordinate |
| <color green>YYY</color> | Upper-left corner Y coordinate |
| <color #BF9F00>SSSS</color> | Texture S coordinate at upper-left corner |
| <color #8F3F10>TTTT</color> | Texture T coordinate at upper-left corner |
| <color #3F3FFF>DDDD</color> | Change in S coordinate over change in X coordinate |
| <color darkcyan>EEEE</color> | Change in T coordinate over change in Y coordinate |

----

==== E5: G_TEXRECTFLIP ====
Draws a textured 2D rectangle on the screen

''E5 [<color darkred>xx x</color>][<color darkgreen>y yy</color>] 0[<color darkblue>I</color>] [<color red>XX X</color>][<color green>Y YY</color>]''\\
''E1 00 00 00 [<color #BF9F00>SS SS</color>] [<color #8F3F10>TT TT</color>]''\\
''F1 00 00 00 [<color #3F3FFF>DD DD</color>] [<color darkcyan>EE EE</color>]''

| <color darkred>xxx</color> | Lower-right corner X coordinate |
| <color darkgreen>yyy</color> | Lower-right corner Y coordinate |
| <color darkblue>I</color> | Tile descriptor to use for rectangle |
| <color red>XXX</color> | Upper-left corner X coordinate |
| <color green>YYY</color> | Upper-left corner Y coordinate |
| <color #BF9F00>SSSS</color> | Texture S coordinate at upper-left corner |
| <color #8F3F10>TTTT</color> | Texture T coordinate at upper-left corner |
| <color #3F3FFF>DDDD</color> | Change in T coordinate over change in X coordinate |
| <color darkcyan>EEEE</color> | Change in S coordinate over change in Y coordinate |


This is similar to opcode E4, with the only difference being that the S and T coordinates of a texture are flipped in rendering, so that S coordinates are along the Y axis and T along the X axis. This essentially flips the texture about the diagonal line (<color red>XXX</color>,<color green>YYY</color>),(<color darkred>xxx</color>,<color darkgreen>yyy</color>).

----
==== E6: G_RDPLOADSYNC ====
This forces a wait for a texture to load, in order to synchronize with pixel rendering. This ensures that loading a new texture won't disrupt the rendering of primitives mid-render.

''E6 00 00 00 00 00 00 00''

----

==== E7: G_RDPPIPESYNC ====
**This is not the "start of display list" command. //There is no such thing.//**

Waits for the RDP to finish rendering its currently-rendering primitive, before updating RDP attributes. This avoids altering the rendering of a primitive in the middle of its render.

''E7 00 00 00 00 00 00 00''

Historically, several model viewers have interpreted this command as somehow starting a display list. **This is not true.** Display lists have no command that starts a display list. To find display lists, the most accurate way would be to find the end display list command (B8) and work backwards, until an invalid display list command is encountered, or to parse byte-code that points to display lists.

----

==== E8: G_RDPTILESYNC ====
Forces a wait for rendering to finish before updating tile descriptor attributes, so as to not disrupt rendering of primitives mid-render.

''E8 00 00 00 00 00 00 00''

----

==== E9: G_RDPFULLSYNC ====
Generates an interrupt for the main CPU when the RDP has finished doing everything. This is typically the last opcode before the "end display list" opcode (B8).

''E9 00 00 00 00 00 00 00''

----

==== EA: G_SETKEYGB ====
Sets the center, scale, and width parameters for the green and blue components for chroma key (see EB for red).

''EA [<color #22b14c>ww w</color>][<color #6060ff>x xx</color>] [<color #b5e61d>cc</color>] [<color #00ff00>ss</color>] [<color #00a2e8>dd</color>] [<color #99d9ea>tt</color>]''

| <color #22b14c>w</color> | Scaled width of half the key window for green |
| <color #6060ff>x</color> | Scaled width of half the key window for blue |
| <color #b5e61d>c</color> | Intensity of active key for green |
| <color #00ff00>s</color> | Reciprocal of size of soft edge, normalized to 0..0xFF, for green |
| <color #00a2e8>d</color> | Intensity of active key for blue |
| <color #99d9ea>t</color> | Reciprocal of size of soft edge, normalized to 0..0xFF, for blue |

<color #22b14c>w</color> and <color #6060ff>x</color> are in an unsigned fixed-point 4.8 format. The other parameters are normal 8-bit unsigned integers.

----

==== EB: G_SETKEYR ====
Sets the scale, center, and width parameters for the red component for chroma key (see EA for blue and green).

''EB 00 00 00 0[<color #ff0000>w ww</color>] [<color #e65858>cc</color>] [<color #ff9090>ss</color>]''

| <color #ff0000>w</color> | Scaled with of half the key window for red |
| <color #e65858>c</color> | Intensity of active key for red |
| <color #ff9090>s</color> | Reciprocal of size of soft edge, normalized to 0..0xFF, for blue |

Sets the scale, center, and width parameters for the red component for chroma key (see EA for blue and green).

<color #ff0000>w</color> is an unsigned fixed-point 4.8 number. <color #e65858>c</color> and <color #ff9090>s</color> are 8-bit unsigned integers.
----

==== EC: G_SETCONVERT ====
Sets the terms need to perform conversion from YUV to RGB. 

''   E    C  00<color #ed1c24>aa aaaa  aaa</color><color #99d9ea>b bbbb  bbbb</color> <color #ff7f27>cccc\\ 
cccc c</color><color #22b14c>ddd  dddd dd</color><color #00a2e8>ee  eeee eee</color><color #B755FF>f  ffff ffff</color>''

| <color #ed1c24>a</color> | **K0** term of conversion matrix |
| <color #99d9ea>b</color> | **K1** term of conversion matrix |
| <color #ff7f27>c</color> | **K2** term of conversion matrix |
| <color #22b14c>d</color> | **K3** term of conversion matrix |
| <color #00a2e8>e</color> | **K4** term of conversion matrix |
| <color #B755FF>f</color> | **K5** term of conversion matrix |

All of the parameters are signed 9-bit numbers, with range -256 ≤ k ≤ 255.
----

==== ED: G_SETSCISSOR ====
Sets the scissoring rectangle.

''ED [<color #00a2e8>xx x</color>][<color #22b14c>y yy</color>] 0[<color #ff7f27>m</color>] [<color #ed1c24>vv v</color>][<color #B755FF>w ww</color>]''

| <color #00a2e8>x</color> | Upper-left X coordinate of rectangle |
| <color #22b14c>y</color> | Upper-left Y coordinate of rectangle |
| <color #ff7f27>m</color> | Interpolation mode setting |
| <color #ed1c24>v</color> | Lower-right X coordinate of rectangle |
| <color #B755FF>w</color> | Lower-right Y coordinate of rectangle |

Valid values for <color #ff7f27>m</color> are:
  * <color #44C3A9>G_SC_NON_INTERLACE</color> = 0
  * <color #44C3A9>G_SC_EVEN_INTERLACE</color> = 2
  * <color #44C3A9>G_SC_ODD_INTERLACE</color> = 3

<color #44C3A9>NON_INTERLACE</color> draws all scanlines, while <color #44C3A9>EVEN</color> and <color #44C3A9>ODD</color> draw only even or odd scanlines, respectively.
----

==== EE: G_SETPRIMDEPTH ====
This sets the Z value for the entire primitive to be rendered, when the source for its depth component is set to be taken from this value. (This could be thought of as the depth version of "flat shading".)

''EE 00 00 00 <color #22b14c>zz zz</color> <color #00a2e8>dd dd</color>''

| <color #22b14c>z</color> | Z value for primitive |
| <color #00a2e8>d</color> | Delta Z value for primitive |

<color #22b14c>z</color> and <color #00a2e8>d</color> are signed 16-bit values. <color #22b14c>z</color> sets the actual depth for the primitive, while <color #00a2e8>d</color> helps rendering of anti-aliased and decal objects (this is usually 0).
----
==== EF: G_RDPSetOtherMode ====
Sets the other mode bits of the RDP.

''EF [<color #ff7f27>HH HH HH</color>] [<color #00a2e8>LL LL LL LL</color>]''

| <color #ff7f27>H</color> | Settings for other mode higher word bits |
| <color #00a2e8>L</color> | Settings for other mode lower word bits |

<color #ff7f27>H</color> is similar to using E3, and <color #00a2e8>L</color> is similar to using E2.

The difference from either E3 or E2 is that this command sets all the bits in both halves of the RDP word (that is, this opcode has no way of limiting what bits are actually affected).

The RSP Geometry Mode word bits' parameters can be found [[https://hack64.net/wiki/doku.php?id=rcpstructs#setothermode|under the RCP structs page.]]

----

==== F0: G_LOADTLUT ====
Tells the RDP to load a number of colors from the texture loaded to a given tile descriptor. The tile descriptor's attributes and other state related to textures inform the RDP how to load the palette, and where to load it to.

''F0 00 00 00 0[<color #00a2e8>t</color>] [<color #ff7f27>cc c</color>]0 00''

| <color #00a2e8>t</color> | Tile descriptor to load from |
| <color #ff7f27>c</color> | ((colour count-1) & 0x3FF) << 2 |

(Note: the count is quadrupled likely due to how palettes are stored in TMEM. Not sure where details on that would be appropriate, though.)
----

==== F1: G_RDPHALF_2 ====
This opcode sets the low half of the generic RDP word.

''F1 00 00 00 [<color #ff7f27>LL LL LL LL</color>]''

| <color #ff7f27>L</color> | New value of low word |

Note: the referenced function also generates opcode E1. See the section on E1 for info on that.

----

==== F2: G_SETTILESIZE ====
Sets the texture coordinates and size

''F2 [<color darkred>SS S</color>][<color darkgreen>T TT</color>] 0[<color #00a2e8>I</color>] [<color purple>WW W</color>][<color darkcyan>H HH</color>]''

| <color darkred>SSS</color> | Upper-left corner of texture to load, S-axis |
| <color darkgreen>TTT</color> | Upper-left corner of texture to load, T-axis |
| <color #00a2e8>I</color> | Tile descriptor to load into |
| <color darkred>W</color> | (width - 1) << 2 |
| <color darkgreen>H</color> | (height - 1) << 2 |


Examples:
  F2 00 00 00 00 07 C0 7C : 32x32 textures
  F2 00 00 00 00 0F C0 7C : 64x32
  F2 00 00 00 00 07 C0 FC : 32x64

----

==== F3: G_LOADBLOCK ====
Determines how much data to load after SETTIMG

''F3 [<color darkred>SS S</color>][<color darkgreen>T TT</color>] 0[<color #00a2e8>I</color>] [<color purple>XX X</color>][<color darkcyan>D DD</color>]''

| <color darkred>SSS</color> | Upper-left corner of texture to load, S-axis |
| <color darkgreen>TTT</color> | Upper-left corner of texture to load, T-axis |
| <color #00a2e8>I</color> | Tile descriptor to load into |
| <color purple>XXX</color> | Number of texels to load to TMEM, minus one |
| <color darkcyan>DDD</color> | dxt |

Some notes on dxt:
<WRAP center round box 60%>
dxt is an unsigned fixed-point 1.11 number, meaning a range of 0 ≤ n ≤ 1.999512. This number has units, namely lines•words-1, where a "word" is 64 bits in length, and a line is one row of the texture. (It may be more easily understood when inverted to get its reciprocal: words/lines. dxt is the reciprocal of the number of 64-bit chunks it takes to get a row of texture.)

When loading an image through this opcode, an internal counter is incremented by dxt for every 64 bits of texture read. When this counter is high enough to turn over to the next integer value (e.g. 0.9 + 0.15 -> 1.05), the current line number is incremented. This is important as odd-numbered rows have their values swapped for interleaved access (the first line read in is line 0, and thus isn't swapped).

Note that if dxt is not a power of two (i.e. only one bit in the value is 'on'), then an error in the counter will accumulate over time, and eventually cause errors in determining where next lines are (when exactly this happens depends on the value and the type of texture being read in).
</WRAP>

Examples:
  F3 00 00 00 07 7F F1 00 : 32x64 16-bit Textures
  F3 00 00 00 07 7F F0 80 : 64x32 16-bit Textures
  F3 00 00 00 07 3F F1 00 : 32x32 16-bit Textures 
  F3 00 00 00 07 FF F1 00 : 64x64 8-bit Textures 

----

==== F4: G_LOADTILE ====
Loads a rectangular portion of the texture being pointed to in DRAM for given tile descriptor into TMEM.

''F4 [<color #ed1c24>ss s</color>][<color #ff7f27>t tt</color>] 0[<color #00a2e8>i</color>] [<color #22b14c>uu u</color>][<color #B755FF>v vv</color>]''

| <color #ed1c24>s</color> | Upper-left corner of tile, S-axis |
| <color #ff7f27>t</color> | Upper-left corner of tile, T-axis |
| <color #00a2e8>i</color> | Tile descriptor being loaded to |
| <color #22b14c>u</color> | Lower-right corner of tile, S-axis |
| <color #B755FF>v</color> | Lower-right corner of tile, T-axis |

(<color #ed1c24>s</color>, <color #ff7f27>t</color>) specifies the upper-left corner of the texture in RAM, offset from its earlier-specified origin, and (<color #22b14c>u</color>, <color #B755FF>v</color>) specifies the lower-right corner of the texture to load.

All coordinate values are in unsigned fixed-point 10.2 format (range 0 ≤ n ≤ 1023.75).
----
==== F5: G_SETTILE ====
Sets the texture properties (ex. mirroring)

''F5 [<color darkred>XX XX XX XX XX XX XX</color>]''

| <color darkred>X</color> | Bit-wise parameters |

Bit-wise parameters:

''  [F  5]  <color red>fff</color><color blue>i i</color><color #c3c3c3>0</color><color green>nn nnnn nnn</color><color #BF9F00>m mmmm mmmm </color>''

''<color #c3c3c3>0000 0</color><color purple>ttt</color> <color #3F3FFF>pppp</color> <color orange>cc</color><color darkred>aa aa</color><color darkblue>ss ss</color><color darkgreen>dd</color> <color #8F3F10>bbbb</color> <color darkcyan>uuuu</color>''
| <color red>fff</color> | Sets color format |
| <color blue>ii</color> | Sets bit size of pixel |
| <color green>nnnnnnnnn</color> | Number of 64-bit values per row |
| <color #BF9F00>mmmmmmmmm</color> | Offset of texture in TMEM |
| <color purple>ttt</color> | Tile descriptor being modified |
| <color #3F3FFF>pppp</color> | Which palette to use for colors (if relevant) |
| <color orange>cc</color> | Clamp and Mirror flags for the T axis |
| <color darkred>aaaa</color> | Sets how much of T axis is shown before wrapping |
| <color darkblue>ssss</color> | Sets the amount to shift T axis values after perspective division |
| <color darkgreen>dd</color> | Clamp and Mirror flags for the S axis |
| <color #8F3F10>bbbb</color> | Sets how much of S axis is shown before wrapping |
| <color darkcyan>uuuu</color> | Sets the amount to shift S axis values after perspective division |

|Color formats|||
| 0 | RGBA | Color and alpha |
| 1 | YUV | Luminance and Chrominance |
| 2 | CI | Index and look-up palette |
| 3 | IA | Grayscale and alpha |
| 4 | I | Grayscale |

|Bit sizes|||
| 0 | 4-bit | I, IA, and CI |
| 1 | 8-bit | I, IA, and CI |
| 2 | 16-bit | RGBA, IA, and YUV |
| 3 | 32-bit | RGBA |

Or simply 
''<color #22b14c>Bitsize</color> = 4*2^(<color #00a2e8>i</color>)''

Examples:
  F5 10 00 00 07 00 00 00 : Settile for RGBA16, followed by another F5 command (rendertile)
  F5 70 00 00 07 00 00 00 : Settile for IA16, followed by another F5 command (rendertile)
  F5 10 10 00 07 01 40 50 : Rendertile for RGBA16 32x32 textures
  F5 10 20 00 07 01 40 60 : Rendertile for RGBA16 64x32 textures
  F5 70 10 00 00 01 40 50 : Rendertile for IA16 32x32 textures
  F5 00 01 00 01 00 00 00 : Settile for palettes loading into TLUT0 in tile descriptor 1
  F5 40 08 00 00 09 80 60 : Rendertile for CI4 64x64 textures with clamping on the T (vertical) axis

----

==== F6: G_FILLRECT ====
Draws a colored rectangle on the screen. Use command 0xF7 to set the color of the rectangle.

''F6 [<color darkred>VV V</color>][<color darkblue>W WW</color>] 00 [<color darkgreen>XX X</color>][<color purple>Y YY</color>]''

| <color darkred>VVV</color> | Lower-right corner of rectangle, X-axis |
| <color darkblue>WWW</color> | Lower-right corner of rectangle, Y-axis |
| <color darkgreen>XXX</color> | Upper-left corner of rectangle, X-axis |
| <color purple>YYY</color> | Upper-left corner of rectangle, Y-axis |

----

==== F7: G_SETFILLCOLOR ====
Sets the fill color for use in fill mode.

''F7 00 00 00 [<color darkred>CC CC CC CC</color>]''

| <color darkred>CCCCCCCC</color> | Fill value for use in fill mode |

----

==== F8: G_SETFOGCOLOR ====
Sets the fog color

''F8 00 00 00 [<color red>RR</color>] [<color green>GG</color>] [<color blue>BB</color>] [<color darkgray>AA</color>]''

| <color red>R</color> | red value |
| <color green>G</color> | green value |
| <color blue>B</color> | blue value |
| <color darkgray>A</color> | alpha: Set to FF unless combiner uses 2-cycle mode |

Example: set the fog for the following polygons to pure green

  F8 00 00 00 00 FF 00 FF

----

==== F9: G_SETBLENDCOLOR ====

Sets the RDP blender's blend color, a general purpose color register available for various purposes in the blender.

''F9 00 00 00 [<color red>RR</color>] [<color green>GG</color>] [<color blue>BB</color>] [<color darkgray>AA</color>]''


| <color red>R</color> | red value |
| <color green>G</color> | green value |
| <color blue>B</color> | blue value |
| <color darkgray>A</color> | alpha value |

Example: make blend colour green and opaque
  FB 00 00 00 00 FF 00 FF

----

==== FA: G_SETPRIMCOLOR ====
Sets the primitive color register of the RDP's color combiner. Also sets two additional values available to the color combiner, the minimum LOD level and an LOD fraction.

''FA 00 [<color #ff7f27>mm</color>] [<color #B755FF>ff</color>] [<color red>RR</color>] [<color green>GG</color>] [<color blue>BB</color>] [<color darkgrey>AA</color>]''

| <color #ff7f27>m</color> | Minimum possible LOD value (clamped to this at minimum) |
| <color #B755FF>f</color> | Primitive LOD fraction for mipmap filtering |
| <color red>R</color> | red value |
| <color green>G</color> | green value |
| <color blue>B</color> | blue value |
| <color darkgray>A</color> | alpha value |

<color #ff7f27>m</color> and <color #B755FF>f</color> are both fixed-point unsigned 0.8 numbers, meaning a range of 0 ≤ n ≤ 0.99609375. <color #ff7f27>m</color> defines the minimum possible value for LOD to have, when the LOD calculated for a particular part of the primitive is less than 1.0. In other words, the LOD of any part of the primitive is clamped at the lower end to max(<color #ff7f27>m</color>, LOD).

<color #B755FF>f</color> specifies a fraction that the programmer can specify for use in the color combiner of the RDP. It's meant to offer a further refinement (XXX verify that, not 100% sure on it) on the linear filtering of two mipmaps.
----

==== FB: G_SETENVCOLOR ====
Sets the environment color for combiner

''FB 00 00 00 [<color red>RR</color>] [<color green>GG</color>] [<color blue>BB</color>] [<color darkgray>AA</color>]''


| <color red>R</color> | red value |
| <color green>G</color> | green value |
| <color blue>B</color> | blue value |
| <color darkgray>A</color> | alpha value |

Example: make everything loaded underneath the command red, and semi-transparent
  FB 00 00 00 FF 00 00 8C

----

==== FC: G_SETCOMBINE ====
Performs combining operations (ex. multi-texturing). The N64's Color Combiner calculates the output color by combining the various source colors and source alphas using the following equation: outputcolor = ( A - B ) * C + D.

''FC [<color green>XX XX XX XX XX XX XX</color>]''

| <color green>X</color> | Equation for blending. Mask is bitwise. |

Bitwise mask for X:

''[<color blue>**aaaa**</color>] [<color #808080>**ccccc**</color>] [<color #339999>**eee**</color>] [<color darkorange>**ggg**</color>] [<color #99CCCC>**iiii**</color>] [<color #663333>**kkkkk**</color>] [<color #FF29B8>**bbbb**</color>] [<color #29B8FF>**jjjj**</color>] [<color #FFC2A3>**mmm**</color>] [<color #999900>**ooo**</color>] [<color #4D2673>**ddd**</color>] [<color #57822B>**fff**</color>] [<color #2B2B82>**hhh**</color>] [<color #D0D071>**lll**</color>] [<color #990000>**nnn**</color>] [<color #00BDBD>**ppp**</color>]''

| <color blue>**a**</color> | variable 'a' for mode 1  (color) |
| <color #FF29B8>**b**</color> | variable 'b' for mode 1  (color) |
| <color #808080>**c**</color> | variable 'c' for mode 1  (color) |
| <color #4D2673>**d**</color> | variable 'd' for mode 1  (color) |
| <color #339999>**e**</color> | variable 'e' for mode 1  (alpha) |
| <color #57822B>**f**</color> | variable 'f' for mode 1  (alpha) | 
| <color darkorange>**g**</color> | variable 'g' for mode 1  (alpha) |
| <color #2B2B82>**h**</color> | variable 'h' for mode 1  (alpha) |
| <color #99CCCC>**i**</color> | variable 'a' for mode 2  (color) |
| <color #29B8FF>**j**</color> | variable 'b' for mode 2  (color) |
| <color #663333>**k**</color> | variable 'c' for mode 2  (color) |
| <color #D0D071>**l**</color> | variable 'd' for mode 2  (color) |
| <color #FFC2A3>**m**</color> | variable 'e' for mode 2  (alpha) |
| <color #990000>**n**</color> | variable 'f' for mode 2  (alpha) |
| <color #999900>**o**</color> | variable 'g' for mode 2  (alpha) |
| <color #00BDBD>**p**</color> | variable 'h' for mode 2  (alpha) |

More information here:

[[http://n64devkit.square7.ch/pro-man/pro12/12-06.htm|N64's Color Combiner]]

Examples:
  FC 12 7F FF FF FF F8 38 : Standard usage for solid RGBA textures
  FC 12 18 24 FF 33 FF FF : Standard usage for alpha RGBA textures


----

==== FD: G_SETTIMG ====
Sets the texture image offset

''FD [<color #c3c3c3>xx</color>] 00 00 [<color purple>bb bb bb bb</color>]''

''[<color #c3c3c3>xx</color>] = <color red>fff</color><color #00a2e8>i i</color>000''

| <color purple>b</color> | Segmented address of texture |
| <color red>f</color> | Texture format |
| <color #00a2e8>i</color> | Texture bit-size | 

|Color formats|||
| 0 | RGBA | Color and alpha |
| 1 | YUV | Luminance and Chrominance |
| 2 | CI | Index and look-up palette |
| 3 | IA | Grayscale and alpha |
| 4 | I | Grayscale |

|Bit sizes|||
| 0 | 4-bit | I, IA, and CI |
| 1 | 8-bit | I, IA, and CI |
| 2 | 16-bit | RGBA, IA, and YUV |
| 3 | 32-bit | RGBA |

Or simply 
''<color #22b14c>Bitsize</color> = 4*2^(<color #00a2e8>i</color>)''

Example: Load texture position from 0x90 in RAM bank 0x04 for RGBA16
  FD 10 00 00 04 00 00 90

----

==== FE: G_SETZIMG ====
Sets the location of the depth buffer

''FE 00 00 00 [<color #00a2e8>ii ii ii ii</color>]''

| <color #00a2e8>i</color> | Segmented address of the depth buffer |

Since the format of the depth buffer is fixed (14-bit Z value and 2-bit dZ value), those parameters are not here, unlike for FD and FF. The width of the depth buffer is shared with the color buffer (see FF), and thus isn't set here.

----

==== FF: G_SETCIMG ====
Sets the location of the color framebuffer, usually a framebuffer that's displayed to the screen.

''FF [<color #c3c3c3>xx</color>] 0[<color #22b14c>w ww</color>] [<color #00a2e8>ii ii ii ii</color>]''

''<color #c3c3c3>xx</color> = <color #ff7f27>fff</color><color #B755FF>s s</color>000 (binary)''

| <color #22b14c>w</color> | Width of the color buffer (-1) |
| <color #00a2e8>i</color> | RAM address of color buffer |
| <color #ff7f27>f</color> | Format of color buffer to be pointed to |
| <color #B755FF>s</color> | Bit size of pixels in color buffer to be pointed to |

The color buffer is set to RAM location <color #00a2e8>i</color>, with a width of <color #22b14c>w</color>. <color #ff7f27>f</color> and <color #B755FF>s</color> are the typical image format enumerations, described in G_Settile.

The location is usually some place set as the framebuffer to show (which is not handled by display lists), but oftentimes will be set to a depth buffer. This is usually done to fill (aka clear) the depth buffer in fill mode.

----
===== References =====
  * http://www.smwcentral.net/?p=viewthread&t=74389
  * http://origami64.net/showthread.php?tid=114
  * http://n64.icequake.net/doc/n64intro/kantan/step2/4-3.html
  * http://jul.rustedlogic.net/thread.php?id=1234
  * http://level42.ca/projects/ultra64/Documentation/man/pro-man/pro25/25-01.html
  * http://wiki.spinout182.com/w/F3DEX2
  * http://wiki.cloudmodding.com/oot/F3DZEX/Opcode_Details
User Tools

Site Tools

Page Tools
